We offer various solutions for the control and regulation of our units, which can be used depending on the application and requirements:

Display

An integrated touch display in the casing is available for operation and control.

Electromechanical control

This variant is ideal for simple applications. All integrated actuators are factory-wired to terminals and can be connected to our electromechanical accessories such as thermostats or external controllers.

KaControl MC1

Our comprehensive comfort control offers extended control options for individual rooms or appliance groups.

It can be operated either via a touch display or a web interface.

Thanks to on-site 0-10V control or common communication protocols such as Modbus RTU & TCP, BACnet and KNX, this solution is ideal for all BMS applications.

Thermostat

Two different room thermostats are available for operation and control (heating only or heating and cooling)

PowerKon LT can be selected in various lengths.

Depending on the structural conditions and installation requirements, two connection variants can be selected:

Left or right connection.

These variants enable optimum adaptation to the pipe routing on site and reduce both installation work and costs.

For wall-mounted units, the connection side is defined from the viewing angle of the mounted unit.

For ceiling-mounted units, please refer to the technical drawing or installation instructions for the definition.

The valve equipment differs as follows:

Without valve equipment:

The units are supplied without pre-assembled valves. A wide range of accessories is available for individual configuration.

With valve equipment:

Assembly is carried out at the factory. Valves and any existing pipework are checked for tightness and sealed after installation. This reduces the installation time on site.

• It is possible to replace existing panel radiators with PowerKon LT radiators.
• The existing pipe network can still be used.
• Determination of the unknown and estimated radiator output for PowerKon LT design is possible using the BWP radiator calculator.
• When using the cooling function with condensate in the existing system, the vapor diffusion tightness of the entire pipe network must be ensured.

• Minimum ground clearance: 100 mm
• Minimum wall clearance: 100 mm
• windowsill min. 100 mm above device
• The windowsill should protrude a maximum of 120 mm into the room.

• simplified hydraulic connection thanks to pre-assembled valve kit with stainless steel corrugated pipes and pressable copper fitting
• Connection side left or right selectable during configuration
• optional connection to the device from the wall or the floor
• Use of existing lines possible

When operating the unit below the dew point, note the following:

• The maximum delivery height of the condensate pump is 6 m from the lower edge of the unit and must not be exceeded.
• Condensate lines must be ventilated or vented.
• Provide lines with a permanent and continuous gradient (1%). Avoid inclines or so-called "water pockets". Use only fixed lines (no flexible hoses) for horizontal lines.
• Connections and transitions (e.g. from hose to fixed line) must be tightly and mechanically secured, e.g. by the use of hose clamps.
• If a siphon stop device is located at the transition point from the device to the on-site drain, it must be mounted at the highest point of the drainage profile.
• Protect condensate-carrying lines against falling below the dew point, e.g. by means of vapour diffusion-tight insulation.

• Complies with the relevant hygiene guideline VDI 6022
• Goal: Ensuring hygienic supply air that is harmless to health
• Applies to common rooms such as workplaces, meeting rooms, break rooms, living rooms, sports facilities and sales rooms.
• With factory-fitted ISO Coarse filter in the intake area.
• Accessibility of all ventilated and water-bearing components for cleaning.

• Considers the environmental impact of the product over its entire life cycle.
• Published as an Environmental Product Declaration (EPD) in accordance with standard EN 15804.
• Available for download at International EPD System.
• Item number-specific life cycle assessment data in the technical data sheets.
• Product is registered in the DGNB Navigator (building product platform).

Serves as proof for certification systems, e.g:

• DGNB (German Sustainable Building Council);
• BREEAM (Building Research Establishment Environmental Assessment Method);
• LEED (Leadership in Energy and Environmental Design).